Blog

Why cellular is a stronger starting point for OT and IoT security

Written by IXT | 14. nov. 2026, 05:00:00

Most OT and IoT security plans start from the network the site already has. An Ethernet segment in a cabinet. Wi-Fi across the factory floor. A VPN back to the control room. Each of those puts every device in the same room as every other device, and the security work then goes into building walls inside that room.

 

Cellular starts from the opposite end. Each device gets its own connection. Nothing talks to anything else until the network allows it. That changes where your security effort goes.

 

 

Shared networks put every device in the same room

On a wired segment or a Wi-Fi network, devices share a broadcast domain. A compromised sensor reaches the controller next to it. Segmentation fixes this, but you add it after the fact, with VLANs, access lists and firewalls, and every rule is one more thing to keep right.

 

Most networks never finish that job. Palo Alto Networks' 2025 Device Security Threat Report found poor segmentation in more than three in four of the enterprise networks it analysed, with IT and IoT devices mixed on the same subnets.

 

The usual tools carry their own risks. Trevor Dearing, who runs the Industry Solutions team at Illumio, pointed out in a recent IXT webinar that VLANs only count as security when dynamic VLAN protocols are switched off. Isolating a suspect device with network access control has taken down large parts of a network.

 

 

Cellular is point-to-point by design

A cellular connection runs from one endpoint to the core network. There is no shared segment where devices see each other by default. Henning Solberg, CTO at IXT, put it this way: cellular "gives that endpoint protection from the ground up."

 

That matters most for the devices that cannot protect themselves. A small microcontroller in an unattended cabinet has no room for an agent, a VPN client or a host firewall. If the device cannot defend itself, the network has to, and cellular gives the network one connection per device to work with before any policy is written.

 

Trevor sees the same shift on site visits. Factories and energy installations are moving to 5G for two reasons. The connection is reliable in a way Wi-Fi is not, because it is connection-oriented. And the sites are easier to secure.

 

 

Where the head start ends

Cellular is a foundation, not a finished design. Two gaps remain.

 

The first is the private APN. It keeps traffic off the public internet, and operators used to treat it as the security boundary. It does not tell you what your devices talk to, and it does not stop one compromised device reaching the rest of the fleet. We cover this gap in the hidden risks of traditional APN connectivity.

 

The second is the router at the edge. Put a 4G or 5G CPE router at a remote site, connect several devices to it over Ethernet, and you have rebuilt a shared segment at the far end of the cellular link. That segment needs micro-segmentation of its own.

 

 

Where cellular is not the answer

Cellular is not the right link for every device. Inside a building with poor signal, such as a basement plant room, a wired connection is more reliable. A site that already has fibre and a well-segmented OT network gains little from moving to cellular. And a cabinet with dozens of devices in one place is better served by one router with proper segmentation behind it than by a SIM in every device.

 

The case for cellular is strongest where devices are spread out, unattended, hard to reach with cable, or owned by several parties who should never share a network.

 

 

What to build on top of the cellular link

Once each device has its own connection, the work is deciding what each one is allowed to reach. IXT does that in the network. The IXT SIM identifies the device. SecureNet keeps its traffic on a private APN. Zscaler ZTNA in IXT's core network checks every session before a connection opens. Illumio shows every connection in real time and applies policy-based segmentation, including behind a CPE router.

 

Trevor's view of the combination: "This solution does simplify things a lot, especially at the headless end for those devices."

 

 

Four questions before you choose

If you are weighing cellular against Ethernet or Wi-Fi for an OT or IoT site, start here. Do the devices run security software, or does the network have to carry it? Do you know every destination each device talks to today? Will third parties need remote access, and how do they get it now? Are several devices sitting behind one router at remote sites?

 

The more of these point to the network doing the work, the stronger the case for cellular. For the wider architecture, read what network-level Zero Trust for IoT devices means, or the eight lessons from our webinar with Illumio.

 

 

Watch the session

Henning and Trevor cover cellular for OT and IoT from 24:02 in the recording.

 

 

Why trust this guide

This guidance is based on real IoT and OT deployments in regulated industries including energy, utilities, and industrial environments.

 

IXT designs and operates secure connectivity architectures where:

  • devices are deployed across multiple countries and networks
  • SIM-level identity is enforced at the network edge
  • third-party access is controlled without VPNs
  • audit trails are required for regulatory compliance (including NIS2)

The patterns described here reflect how these environments are secured in practice, not theoretical models.

 

 

About the author

This article was written by the IXT Connectivity and Security team.

IXT operates a full MVNO core network and delivers secure IoT connectivity across 190+ countries and 600+ mobile networks. The team works directly with industrial, utilities, and infrastructure operators to design and secure large-scale IoT and OT deployments.

Their focus is on network-level Zero Trust architecture, SIM-based identity, and secure device communication without relying on VPNs or endpoint agents.